How do I know if I need a cassette spacer?
Put the cassette on w/o the spacer: if you tighten down the lockring and there is side to side play of the cassette on the freehub, you need a spacer. Put the cassette on w/ a spacer: if you cannot engage the lockring with the freehub threading, you need to remove it.
What spacer for 10 speed cassette on 11 speed hub?
Note: When using a 10-speed Shimano road cassette on an 11-Speed freehub body, you need both 1mm and the 1.85mm additional spacer (not included). When using a 10-speed Shimano road cassette on an Mavic M10 freehub body, you need both 1mm and the 1.75mm additional spacer (not included).
Are all 10 speed cassettes the same width?
8, 9, and 10 speed Shimano and Sram cassettes are the same width. You can ‘upgrade’ without any other modifications. Your shifters will determine what speed cassette and chain you use. If 9 speed it is a direct swap, if 10 speed there is an additional spacer between hub and cassette that should come with the cassette.
Do I need a spacer for a 12 speed cassette?
No, do not use a spacer with the 10-44T cassette. The 12-speed 10-44T cassette is designed specifically for the XDR driver. Was this article helpful?
Does my 10 speed cassette need a spacer?
SHIMANO 10 CASSETTE You’ll need to fit the 1.85mm spacer which was included with your hub, PLUS the 1.0mm spacer which was included with your cassette.
What happens if you don’t use a spacer?
If you use your inhaler without a spacer, then most of the medicine ends up inside your mouth or stomach, instead of your lungs, where it works best. The spacer acts as a holding chamber where the medicine sits as a fine mist that you can then breathe in very slowly.
Can I run a 10 speed cassette on 11 speed?
Use spacers on the 11 speed wheel to put a 10 speed cassette on. See your hub manufacturer’s page for details, but its normally a 1.8(5) mm spacer (which comes with the hub, but you can buy separately) and a 1mm spacer (sometimes; which you’ll get with the cassette).
Are 10 speed and 11 speed hubs compatible?
You cannot run 11 or 12 speed cassettes on these 10 speed only freehubs. Non-10 speed cassettes won’t likely fit as splines on the 10 speed freehubs were taller.
How long should a 10 speed cassette last?
If you clean the drivetrain usually and lube it, considering a normal use, for road cycling the 105 should last around 3–4000 km. For mtb, the deore should be around 2.500km. But you need to change it when the teeth on your cassette look like arrowpoints insted of ending in a bezel.
Is an 11-28 cassette good for climbing?
There are different cassette ratios. There are 11/25 and 12/25 for flat riding, while 11/28 or 11/30 cassettes are suitable for hilly courses and for some riders, suffice in the mountains. For most cyclists, however, the 11/32 and 11/34 cassettes are best suited for steep climbs.
Are all 10 speed cassettes compatible?
All Shimano and SRAM cassettes up to 10 speed are broadly compatible. They all use Shimano’s Hyperglide II freehub body spline pattern. Cassettes with the same number of sprockets have the same sprocket spacing, sprocket width and overall width.
Do I have to use a spacer?
In general, using the inhaler without a spacer requires more coordination in order to ensure that medicine reaches your lungs. So, when possible, it’s best to use a spacer. These are instructions for using an inhaler without a spacer. First off, if you have not used the inhaler in a while, you may need to prime it.
Do I need a spacer?
Incorrect technique can leave some of the particles from the medicine on your tongue or throat, where it won’t help at all. A spacer, or holding chamber, is an attachment that should always be used with your inhaler. The spacer holds the medicine in place so you can breathe it in easier.
Does a 12 speed cassette need a spacer?
For SRAM 12-speed road cassettes, no spacer is required.
Do I need volume spacers?
While this adjustment is a lot to do with personal preference, there’s a range of situations in which volume spacers are very useful. Firstly, if you’ve got your sag set up properly but you’re still regularly bottoming out your suspension, adding volume spacers can fix this without having to add more air pressure.
Are 10 and 11 speed cassettes the same width?
The 10spd axle is the same width as the 11spd. The 8/9/10 speed freehub body is shorter than an 11spd (since the cassettes are not as wide). So if you wanted to put a 10spd cassette on an 11spd hub you add a spacer at the back.
What can I use instead of a spacer?
Simple spacers can be made with plastic bottles, Styrofoam cups, plastic baggies, paper, or even toilet paper rolls. This kind of hack is especially useful for non-medical settings or places with little money to spend on medical devices.
What are the disadvantages of spacers?
The larger the spacer, the larger the leverage becomes. This reduces the life of the wheel bearing as they are not made to take leverage forces and can therefore wear faster, increasing rolling resistance and power loss of the car.
Do I need a spacer for 10 speed MTB cassette?
Most Shimano 10-speed cassettes road cassettes come with a 1mm spacer. It is intended to and should be installed whenever it can fit on the freehub body. Mountain cassettes never include or use this spacer.
What cassette is best for climbing?
For most assistance on the ascents when riding on the road an 11-32 to 11-36 may prove most beneficial. Closer ratio cassettes such as 11/25, 11/28 or 11/30 are better for riders with a high level of fitness or who prefer flatter terrain.
Can I replace a 9 speed cassette with a 10 speed?
You can put a new 10 or 11 speed cassette on any of the older 9 speed hubs. So, regardless of brand, feel free to buy your wheels a nicely upgraded new steed.
How do I know if I need spacers?
The interior space increases, hence the possibility of tire rubbing reduces. This is helpful when it comes to adding a performance brake kit. In short, when a wheel clearance issue occurs, you will need wheel spacers.
Do I need volume spacers?
While this adjustment is a lot to do with personal preference, there’s a range of situations in which volume spacers are very useful. Firstly, if you’ve got your sag set up properly but you’re still regularly bottoming out your suspension, adding volume spacers can fix this without having to add more air pressure.
Do I have to use a spacer?
In general, using the inhaler without a spacer requires more coordination in order to ensure that medicine reaches your lungs. So, when possible, it’s best to use a spacer. These are instructions for using an inhaler without a spacer. First off, if you have not used the inhaler in a while, you may need to prime it.
Do I need a spacer?
Incorrect technique can leave some of the particles from the medicine on your tongue or throat, where it won’t help at all. A spacer, or holding chamber, is an attachment that should always be used with your inhaler. The spacer holds the medicine in place so you can breathe it in easier.
What is the right combination of spacers for a 10 speed cassette?
Do I need a spacer for a 11 speed cassette?
Can a Shimano 8 speed hub fit a 10 speed cassette?
What size spacer do I need for a Shimano cassette?
First things first, what is a spacer? Think of it as a little metal ring that goes between your cassette and your freehub body. It’s basically there to fill up any extra space and make sure everything fits snugly.
Now, do you always need a spacer with a 10-speed cassette? The answer is a little complicated, but here’s the deal: it depends.
Here’s the thing:
Older 10-speed cassettes: They were often made for freehub bodies that had a 1.85mmaxlediameter. This meant that if you had a 10-speed cassette and a 1.85mmfreehub body, you’d need a spacer. This spacer was there to take up the extra space between the cassette and the freehub body.
Newer 10-speed cassettes: They’re designed for 1.85mmfreehub bodies, but they don’t always need a spacer.
So, how do you know if you need a spacer or not? Well, here’s a quick way to figure it out:
1. Check the freehub body: It should say “10-speed” or “1.85mm” on it.
2. Check the cassette: It should say “10-speed” on it.
If both say 10-speed, you’ll probably need a spacer.
But there’s another wrinkle!
Some modern 10-speed cassettes, even though they fit on a 1.85mm freehub body, are designed without the need for a spacer. This means you can install them directly onto your freehub body.
Now, how do you tell if your 10-speed cassette is designed with or without a spacer?
Look at the cassette. Does it have a spacer built into the smallest cog? If so, then you’re good to go!
Read the instructions that came with your cassette.
Why is this important?
Well, if you don’t use a spacer when you need one, things can go wrong.
* Your cassette might not shift smoothly.
* It might fall off the freehub body altogether!
* You could even damage your freehub body.
Here’s the bottom line:
If you have a 10-speed cassette and an older 1.85mm freehub body, you’ll probably need a spacer.
If you have a 10-speed cassette and a modern 1.85mm freehub body, you might or might not need a spacer.
Check the instructions that came with your cassette and/or look closely at the cassette itself.
Now, let’s talk about the importance of spacers and why they are so important.
Spacers act as the glue that holds your cassette to your freehub body. They make sure that the cassette fits snugly and securely, so it doesn’t shift or fall off.
Think about it this way: a spacer is like a shim that fills up any extra space so that there’s no movement or play between the cassette and the freehub body.
Here’s why using the right spacer is so important:
Smooth shifting: A spacer ensures that your cassette is properly aligned, which helps your gears shift smoothly and precisely.
Prevent wear and tear: A spacer prevents the cassette from rubbing against the freehub body, which can cause wear and tear on both components.
Safety: If your cassette isn’t secured properly, it could fall off while you’re riding, which could be dangerous!
Okay, I know this might seem confusing, but let’s break it down even further.
Here’s a table that might help:
| Freehub Body Type | Cassette Type | Spacer Needed? |
|—|—|—|
| 1.85mm (Older) | 10-speed (older) | Yes |
| 1.85mm (Older) | 10-speed (newer) | Maybe |
| 1.85mm (Newer) | 10-speed (newer) | Maybe |
Remember, if you’re unsure whether you need a spacer or not, it’s best to consult your bike shop or a knowledgeable mechanic. They can help you determine the right spacer for your specific setup.
How to install a spacer:
1. Make sure your bike is secure. Put it on a stand or have someone hold it steady.
2. Remove your existing cassette. You’ll need a cassette lockring tool for this.
3. Place the spacer on the freehub body. Make sure it’s facing the right way.
4. Install your cassette.
5. Tighten the lockring.
Now let’s answer some frequently asked questions:
FAQs:
1. How do I know what size spacer I need?
The size of the spacer you need will depend on the type of freehub body you have and the type of cassette you’re using.
Older 1.85mm freehub bodies usually need a 1.85mm spacer.
Newer 1.85mm freehub bodies might not need a spacer, but it’s best to check the instructions that came with your cassette.
2. What if I don’t have the right spacer?
You can usually find spacers at your local bike shop, or you can order them online.
3. Can I use a spacer from a different cassette?
It’s not recommended to use a spacer from a different cassette, as it might not be the right size.
4. What if my cassette doesn’t shift smoothly after installing a spacer?
If your cassette doesn’t shift smoothly after installing a spacer, it could be that the spacer isn’t installed correctly, or it might be the wrong size.
5. Can I use a spacer if my cassette has a spacer built in?
No, if your cassette already has a spacer built in, you don’t need to use another one.
I hope this article helped clear things up for you! Remember, it’s always best to consult a mechanic if you’re unsure about anything.
Happy riding!
See more here: What Spacer For 10 Speed Cassette On 11 Speed Hub? | Does A 10 Speed Cassette Need A Spacer
Do I need a spacer between my cassette and freehub?
I am fitting a modern Shimano 10-speed Hyperglide cassette ( CS-HG81-10) to an old Shimano 8 speed hub ( FH-M565 ). Fortunately, it is long enough (approx. 35mm) to take 10-speed. The hub came with a spacer and I am not sure if I should use it or not. Bicycles Stack Exchange
How do I know if I need a cassette spacer or not —
The 1.85mm is necessary if you have an 11-speed freehub but are using a 9 or 10-speed cassette. The 1.0mm spacer is used if you are using a 10-speed cassette, the 10 BikeRadar
Do you need the spacer for Shimano 10 speed cassette?
Swapped the 10 speed Ultegra cassette over with supplied spacer, but when in the highest gear at the back and on the middle ring the angle means the chain Road Bike, Cycling Forums
What is the right combination of spacers for a 10 speed cassette
ID360 Mavic hubs have standard Shimano HG road 11 splines, so you can use a standard 1.85mm spacer for a HG 10-speed MTB cassette, and the additional Bicycles Stack Exchange
Shimano 10 speed cassette with 1mm spacer on 10 speed freehub
Installing a Shimano 10 speed cassette CS-6700 with a 1mm spacer on a 10 speed freehub. The 1mm spacer is required for the lock ring to engage the cassette so YouTube
WHAT CASSETTE SPACERS DO I NEED? – Wheelworks
SRAM 10 CASSETTE. You’ll need to fit the 1.85mm spacer which was included with your hub. SHIMANO 11 OR SRAM 11 CASSETTE. No spacers are required. REMEMBER: • Wheelworks
Shimano Rs100 and 10speed cassette. Do I need spacers
Yes. You need a 1.85mm spacer. If your cassette is 105, ultegra or dura ace you’ll also need a 1mm spacer. Singletrack World Magazine
How to secceussfully use a Shimano 10-speed casette
10 speed cassettes are 1.85mm narrower than 11 speed cassettes. You also need this spacer to use your 10 speed cassette on an 11 speed wheelset. The more you know! Reddit
Where do the spacers go on Shimano 10 speed cassettes?
You also need a 1mm thick spacer on the freehub, before you put the cassette on. Those normally come with the cassette but an ebay seller might not have Road Bike, Cycling Forums
See more new information: charoenmotorcycles.com
How To Use Bike Cassette Spacers | Monday Maintenance
Hg Freehubs And Cassette Spacers
Tech Tip Tuesday – 1.8Mm Cassette Spacer
Cassette Spacers: 8 Speed On 11 Speed Hub
Can I Update Wheel From 7 Speed Cassette To 8, 9, Or 10 Speed Cassette?
Cassette Spacers? Mountain Bike Cassette Assembly For Anyone Confused About Where The Spacers Go.
Shimano 10 Speed Cassette With 1Mm Spacer On 10 Speed Freehub
7 Speed Cassette On 8/9/10 Speed Hub Without Spacer
How To Hack Mtb Cassette 9S To 10S | No Need Change Shifter
Link to this article: does a 10 speed cassette need a spacer.
See more articles in the same category here: https://charoenmotorcycles.com/how